sub banner

Hickory Cabinet Hardware
Installation and Alignment Guides

Hickory Hardware

We stock these assorted Mounting Guides from Hickory Hardware.

PBH3100

PBH3100
35MM Concealed Hinge Cup Mounting Kit

Includes 35mm Boring Bit and Clear Plastic Template.

$11.59 ea.

  Qty:

Step A
Mark center point of top and bottom hinge location on door back at equal distance from top and bottom of door. Any center hinges should be equal distance from hinges on either side.

Step B
Position template against hinge side of door at locations markd. Mark center point to be drilled for 35MM hole. Place center point of 35MM drill bit on marked position and drill slowly to 1/2" depth. DO NOT DRILL COMPLETELY THROUGH THE DOOR.

Step C
Position hinge cup in 35MM hole and verify marked pilot hole positions. Most major brands use pilot holes "A" and "B". For others, make changes where necessary before drilling 1/16" pilot holes.

Guides Menu


PBH3101

PBH3101
Cabinet Drawer Precision Alignment Guide

Center to Center Measurements for Cabinet and Drawers, Clear Plastic Template.

  • 3 inch
  • 3½ inch
  • 4 inch
  • 4½ inch
  • 5 inch
  • 64mm
  • 96mm
  • 128mm

Easy Mount for Knobs and Pulls

$3.99 ea.

  Qty:

Center Mount

PBH3101

Step A
Measure the width of the drawer. Be exact.

Step B
Find the exact middle point and mark it. For instance: a 24 inch drawer - the mid-point is 12 inches.

Step C
Align the center point of the guide directly over the middle point. Mark the center point.

Step D
Drill from the outside of the drawer to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.

PBH3101

PBH3101

PBH3101

PBH3101

Double Mount

PBH3101

Step A
Measure the distance of your choice from the outside of the drawer. Mark both sides.

Step B
Mark the measurements. Be exact.

Step C
Align the center line of the guide directly over each point and mark.

Step D
Drill from the outside of the drawer to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.

 

Guides Menu


PBH3103

PBH3103
Cabinet Door and Drawer Precision Alignment Guides with 3/16" Drill Bit

Center to Center Measurements for Cabinet and Drawers with Drill Bit Included, Clear Plastic Templates.

  • 3 inch
  • 3½ inch
  • 4 inch
  • 4½"
  • 5 inch
  • 64mm
  • 96mm
  • 128mm

Easy Mount for Knobs and Pulls

$7.49 ea.

  Qty:

Center Mount

PBH3101

Step A
Measure the width of the drawer. Be exact.

Step B
Find the exact middle point and mark it. For instance: a 24 inch drawer - the mid-point is 12 inches.

Step C
Align the center point of the guide directly over the middle point. Mark the center point.

Step D
Drill from the outside of the drawer to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.

 
Double Mount

PBH3101

Step A
Measure the distance of your choice from the outside of the drawer. Mark both sides.

Step B
Mark the measurements. Be exact.

Step C
Align the center line of the guide directly over each point and mark.

Step D
Drill from the outside of the drawer to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.

   
Knobs

Step A
Door Mount: Choose one of the lower 5 holes on the template. For high mount knobs, use a higher selection on the template.

Step B
Place template flush against the door and mark selected hole. Template works on both sides of the cabinet.

Step C
Drill from the outside of the door to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.

Step D
Insert mounting screw from the back of the door and tighten.

Pulls

Step A
Door Mount: Use 3", 3½", 4" or 96MM, whichever pulls you have chosen.

Step B
Place template flush against the door and mark selected hole. Template works on both sides of the cabinet.

Step C
Drill from the outside of the door to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.

Step D
Insert mounting screw from the back of the door and tighten.

 

Guides Menu


PBH3104

PBH3104
Cabinet Door Precision Alignment Guide

Center to Center Measurements for Cabinet Doors, Clear Plastic Template.

  • 3 inch High
  • 3 inch Low
  • 3½ inch
  • 4 inch
  • 96mm

Easy Mount for Knobs and Pulls

$3.99 ea.

  Qty:

Knobs
PBH3104 Step A
Door Mount: Choose one of the lower 5 holes on the template. For high mount knobs, use a higher selection on the template.
PBH3104 Step B
Place template flush against the door and mark selected hole. Template works on both sides of the cabinet.
PBH3104 Step C
Drill from the outside of the drawer to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.
PBH3104 Step D
Insert mounting screw from the back of the door and tighten.

Pulls
PBH3104 Step A
Door Mount: Use 3", 3½", 4" or 96MM, whichever pulls you have chosen.
PBH3104 Step B
Place template flush against the door and mark selected hole. Template works on both sides of the cabinet.
PBH3104 Step C
Drill slowly from the outside of the drawer to the inside. A 3/16" drill bit is recommended to allow for final adjustments to the alignment.
PBH3104 Step D
Insert mounting screw from the back of the door and tighten.

 

Guides Menu


Cabinet Hardware Menu
Page 1

Page 3

Page 2

Page 4


Mouldings

Decorative Polyurethane Medallions

Randall Thresholds/Mouldings

Pole Wrap for Finishing Basement Poles

Band-It Real Wood Veneer and Edging

Johnson Quality Door Hardware

 

Fox Home Page
Receive a copy of our
current advertising flyer by mail!
QUESTIONS? Email Us
image